-
A guitarist friend ( he plays Rock and Blues on High Wattage Amps) swears that go get proper tone on tube amps, they must be allowed around 30 minutes warm-up time. Now I have noticed a difference in tone by letting my '65 DRRI and other large amps have several minutes to warm up, but 30 minutes? Doesn't that sound excessive?
I don't have enough experience to speak about this subject. Can anyone share their warm-up habits with their tube amps?
-
06-18-2019 04:49 PM
-
I thought that's what the standby selection on the three-way power switch was for on tube amps. The middle position was off, one side of middle position was on and the other side was stand by.
And when I owned tube amps I preferred them to have an outlet on the back so I could plug my muffin fan in and try to keep things cool(er).Last edited by geogio; 06-18-2019 at 09:21 PM.
-
Ask your friend where he got the information about high power tube amps needing a 30 minute warm up.
I've asked amp techs about this and each recommended about 5 minutes. Unless you are 'burning in' a brand new amp or new tubes, why would you need more than that?
Some players claim to hear stuff in amps and guitars that we mere mortals cannot. Maybe they can. Maybe they are just blowing smoke.
But when it comes to blanket statements about electronics, it helps if they have credibility, training, experience...or not.
-
Originally Posted by Gitfiddler
-
Complete nonsense.
what he’s experiencing may very well be his ears fatiguing after prolonged exposure to excessive volume.
Me? I turn on the amp and play.
-
Originally Posted by AlsoRan
John.
-
In the old Jukeboxes the amplifier was off until you put your nickel in, then in order to have it up and running high voltage somewhere around 100 volts was applied to the 6 volt filament supply. There was a relay in series with the output plate circuit as soon as the plate current came up to operating current it pulled in and dropped the filament voltages to 6 volts.
So the amp was up and running when the needle hit the record. It took seconds.
There may be some difference when the whole tube is hot but it is doubtful it sounds or lasts differently.
It is back to if you believe it sounds different then it does.
-
Fiction. You and your amp may (nay, should!) sound better after 30 minutes of playing time, but IMO its a matter of warming up the hands and focusing the mind.
That's why I always arrived early enough to the gig to get in at least an hour's worth of un-plugged playing. I did a long stretch with a band that liked to open with "Crossroads" or "I know a Little" or, all too often, both. No pressure.
-
Thanks for sharing your experience. I looked around on the web and this is another one of those controversial topics. There are many threads and articles out there that say 20 to 30 minutes or so. Then there are others that say right away.
My buddy's dad played guitar for many years and he is the one who started my buddy thinking this. He even found where some manufacturer's recommended 20 to 30 minutes.
Go figure
-
You really need to be playing to give the amp/tubes some work to do, that's what gets it hot.
-
I have gigged for 50 years. In that time I've gotten to the venue early enough to put my tube amps into standby at least 30 minutes prior to the first set.
-
Originally Posted by cosmic gumbo
-
Originally Posted by geogio
-
Technically speaking, it's a lot closer to five SECONDS than thirty minutes. Any other take on the subject belongs to the realm of myths and urban legends.
I guess guitar players are just suckers for fairy tales? Gee, I can't quite tell.
-
Originally Posted by vintagelove
-
I have often noticed that too with my tube amps. About 30 minutes into the gig (cause I almost never warm them up for more than a couple of minutes), they start to sound different and then stay that way for the rest of the gig. I've always assumed it's the amp (tubes?) reaching its working temperature. I've never actually checked it, but it should be easy to compare the two situations.
Come to think of it, most experienced guitarists I know believe that it is so too, and many do warm their amps for an extensive time before the gig. No idea if it holds true though
-
enough 40 second
-
Originally Posted by Alter
I don't have the issue with the same gear at home. I believe that's because I know what it's going to sound like, I'm accustomed to it, and I don't need to adjust.
This would require a recording studio to evaluate. Otherwise, it's so confounded with human perception that it would be difficult to feel certain that anything was really different about the amp.
Maybe it's the cable relaxing after been wound up in my gear bag.
-
I understand what you are describing, and it does happen to me too, especially if I play close gigs with different gear and bands. After a while you do get extremely comfortable with the gear, the room, the whole playing situation and you do sound better. But I feel there might be some truth to the 30 minute theory as well. It should be easy to test in a studio, turn on and record a looper play. Let it play for 30 minutes, record again.
-
I have heard stories of guys of the EVH type turning their amps on in early afternoon and leaving them on in preparation for 9pm concert. I’m guessing this where such a rumor emanates from. I’ve also read of at least a couple of similar guys who play with their amps “on 11” that had their techs replace all tubes after the very show!
-
The purpose of the standby switch is to kill the volume for a short time during a break, so howling feedback doesn't set in while you're away. It has no other purpose. I remember when every electronic device used tubes - radios, phonographs, eventually TVs, - everything, and none had a standby switch. You just turned it on and waited until it started working. It took a few seconds for the tubes to warm up, but it didn't affect anything otherwise. Waiting for minutes with the standby switch engaged is a complete waste of time. I only use it if I intend to leave the room for awhile, and don't want to bother to turn the amp off while I'm gone. But the old wives have innumerable tales, and they never die.
-
"no other purpose"
The standby switch IS there for breaks, but its purpose is to prevent having to cold start the tubes.
When power is applied to a vacuum tube some of the thoriated tungsten filament on the cathode is stripped until the tube comes up to operating temperature from the heater element. This ages the tube.
Standby interrupts the plate voltage on the tube while keeping the heaters going. This extends tube life.
Always start up on standby too, going to on after a minute or so.
-
NEED a warm-up? No. I've read it WAY to many times from WAY too many experts/techs that a warm-up (or a standby switch) is not necessary... especially with amps that have tube rectifiers.
However, I have always found amps sound better when running hot. But they don't need 30 minutes to get there.
-
Originally Posted by whiskey02
-
Originally Posted by Greentone
The Unwritten Theory of Guitar Harmolodics
Yesterday, 07:33 PM in Guitar Technique