-
Hello all
I just got a Djangobucker pickup for my selmer style guitar. It just has a 1/4" plug at the end of a long chord.
I'd like to switch it over to a jack that I can velcro on the guitar where the endpin would be (so I can semi permanently mount it but take it off easily if I need to).
I can't seem to find a 1/4" jack with any sort of velcro attachment. One of my piezo pickups has something but it's sort of a rube goldberg collection of pieces.
Is there such a thing? Basically a 1/4" jack permanently or semi permanently attached to a velco pad?
-
01-22-2020 11:11 AM
-
It's not that hard to wrap some sticky-back Velcro around a jack. You can buy it in a variety of widths, in both hook and loop.
-
Originally Posted by sgosnell
-
Some of the Velcro I've used has very strong adhesive. The products made for outdoor use, billed as "extreme", have adhesive that is stronger than almost any other pliable adhesive I've found. It's at least as strong as the strongest mounting tape I've used, probably because it can't stretch like mounting tape. Once you put that on something like a jack, you'll have to work very hard to remove it. Of course, there are varying strengths available, some much weaker than these.
-
ok cool I just ordered a switchcraft jack to wire the pickup too. I'm pondering epoxying the jack to a square of wood and putting the velcro on that but we will see how it goes.
Thanks!!
-
FYI: I have a Favino GJ guitar where I put a strip of Velcro backing on the bottom of the tailpiece. I was never too happy with this setup. It tended to collect lint and dirt and stick to the the carpet if I set it down. While it kept the jack in place, you had to be careful and hold it tightly when plugging in or unplugging the guitar cable. Otherwise, it would rip the whole thing away from the Velcro backing on the tailpiece. Part of the reason is that since the jack was round the Velcro didn't have much contact with the backing strip. And I used a medium/heavy grade of Velcro backing.
In the long run, I chose to attach and detach the pickup when I needed it. BTW, a lot of GJ pickups like Stimer and Peche ala Mouche have cables attached to the pickup with the intent being you take the pickup on and off when you need to use it. That's what I do with my Peche ala Mouche, and frankly, it's worth the effort since I think it is the best sounding GJ pickup I have. I prefer it to on-board systems like Big Tone and K&K.
-
Thanks for the advice. I hate to say it's an aescetic decision but I really hate the look of the cable hanging off the guitar.
I was planning on velcroing it to the endpin area of the guitar (on the wood) and hope that it will be a little stiffer there. We'll see.
Really I'd like an F hole guitar with a permanently mounted covered pickup but that's a ways off.
-
Understand Sully what you're saying about aescetics. Keep in mind, the backing on the Velcro can be pretty sticky -- like permanently sticky. If you put it on the wood and ever go to remove it, it might take off the finish. If it doesn't harm the finish but just leaves a sticky residue, that can be removed with a little bit of naphtha. That's why to avoid any potential problems I put mine on the metal part of my tailpiece.
By the way, the Krivo Djangobucker sounds like a good choice. Let us know what you think about it. (Be sure to mention your guitar brand and amp too. We are a curious bunch indeed!)
-
I occasionally use a Dearmond guitar mic on my L5. I wrapped Velcro tape around the jack, and put a 1/2” square on the underside of the pick guard. It works a charm.
-
Maybe one of those jacks made to replaced the strap pin?
The pickup wire goes directly to the jack, inside the guitar.
-
Endpin jacks work pretty well, and aren't too hard to install, if you have the proper tools. I would not put the Velcro directly onto the wood. That can have disastrous results. You can put it on the tailpiece, or under the pickguard. Using this method means you really need to remove the jack and hold it when you insert or remove the instrument cable, it's not likely to hold in place without help. The Velcro is just to keep it in place while playing.
-
The issue with this pickup is that it sits on top of the guitar and I'd like it to be removable. So an endpin thing won't really work because the cord would come out the soundhole and I wouldn't be able to take it on and off (for one thing the soundhole on a selmac is too small to get your hand in).
It's a $600 Altamira. It's already got some gaffers tape and a furniture pad on the lower bout to keep it from slipping on my leg. It's a nice guitar but I don't feel any need to baby it. The finish seems pretty tough too.
-
Originally Posted by sully75
-
Originally Posted by Woody Sound
I would definitely like a nicer guitar at some point but I think the point is to play the things.
-
You can buy inline mini jacks and plugs pretty cheap. You could run a cable from the endpin jack out the f hole and to the pickguard, with a mini jack there, and a matching plug on the pickup, so you would just unplug it and go. But it may be more trouble than it's worth to you. I have that sort of setup on a couple of guitars on which I tend to change pickups now and then. The cable and jack just stays inside the guitar, and I put a plug on the pickups, so it's a quick change. But everyone's needs and preferences are different, so whatever works for you...
-
Originally Posted by sgosnell
-
Originally Posted by sgosnell
-
Originally Posted by archtopeddy
-
Or Velcro.
-
Originally Posted by sgosnell
Moffa Mithra
Today, 08:31 AM in For Sale