-
Stunning!
-
12-14-2017 10:39 AM
-
Originally Posted by guido5
-
What do you plan to use for shielding? There are many options, including conductive paint, copper or aluminum tape, or even just glued-in aluminum foil. If I were doing many I would use the paint, because it's quick and easy, but for a one-off it's not worth the cost and shipping time since I already have tape on hand.
-
Originally Posted by sgosnell
-
OK, that will work. Like I said, there are many options, and most work, more or less. The StewMac kit should be a good choice.
-
Originally Posted by sgosnell
-
Shield the back of the pickguard, extend the shielding from the cavity onto the top of the guitar and it will make contact and continuity.
If no pickguard, run a length of thin insulated wire through the wiring channel and solder the ends to the shielding in the respective cavities.
Watch out for ground loops.
-
Originally Posted by Cunamara
I thought about doing the wire thing, but thought that might be overkill. Will do it, though.
-
I don't think it's essential, or even usual, to provide electrical continuity between the cavities. Your aim is to create a Faraday cage around the pickups, and the controls. But if you want to do it, you can put ring connectors on wires, and screw the connectors into the bottom of the pickup cavities, then to the control cavity and solder to the volume pot with everything else. Or just wrap the end of the wire around the screw if you don't want to deal with ring connectors. Obviously you'll need a ground wire from the common ground to the strings, however you do that. There should already be a hole drilled for that, and I'm probably wearing my Capt. Obvious uniform here.
-
Shielding:
-
Looks good. You are on a roll with that thing...
-
Originally Posted by guido5
There's a jam session on New Years Day and I'm hoping to have it ready for that. A lot's going to depend on how fast Armadillo can get my new stuff out. From what Mike was saying the other day, it sounds like he's almost ready to ship.
-
Best of luck! Waiting for stuff is no fun at all...
-
Originally Posted by guido5
-
It's starting to look like a guitar!
Pickups, pots, jack and tuners mounted. (Pots and jack mounted for fit - I'll take them off for wiring. Neck is not bolted on. Just dry fit in place to get the full picture).
-
That's starting to look sort of like a telecaster.
-
coming along nicely!!..fretboard looks like flattish 12"/+ radius..or is it warmoth special compound radius?
make sure to roll those fretboard edges...it will really soften it for your fretting hand...broken in comfy feel...looks softer aesthetically too
cheers
-
Originally Posted by neatomic
It's 10-16.
-
Strap buttons and selector switch mounted:
Check out this sweet switch tip from Armadillo! I even found some brass screws to mount the switch with.
All that's left is the bridge and ferrules. I'm going to wire it up today, and as soon as I get those things I can string it up.
-
Most hardware stores have brass screws of various sizes. That's going to be a nice-looking guitar. Enjoy it. Using something you made yourself, or at least had a major hand in making, is a pleasure.
-
Wow, this looks great.
I liked the compound radius on my Warmoth neck almost instantly.
-
Originally Posted by mr. beaumont
-
Finally got the properly sized bridge and ferrules:
-
Oh my is that dark and mysteriously lovely!
-
That's a very nice looking bridge. The design seems much better than the original Fender. The ferrules don't fit into the body holes, but they should work like that, as long as they don't fall off when you change the strings. Even if they do, they can be replaced, it's just a PITA to find them on the floor and pick them up. That's a nice looking Tele, and it will probably sound good, too.
Gibson Thin line Guitar Models
Yesterday, 11:07 PM in Guitar, Amps & Gizmos