-
I am a T-I Swing fan too. Love the slightly smother sound vs. Chromes. Love the balanced tension in the sets - which is pretty much unique in the string world for some reason. Love the feel. Like that they are nickel vs. steel. Like that they do not have grinding dust all over them (and presumably between the windings) like the other nickel wound European flats. Not too crazy about the ever-rising cost, but still a bargain in my opinion.
So a mix of rational and irrational preference.
I like the round BeBops too, but need to buy a wound G for the .012 set. Also, at $3.99 a set, the Fender 150 JL is remarkably close to the .012 BeBops and come with a wound G already.
ChrisLast edited by PTChristopher2; 01-26-2014 at 06:40 PM. Reason: spelling
-
01-26-2014 06:38 PM
-
On my Eastman I had the same problem, and did this:
- removed all the old strings, using some blue-tack to leave the bridge in place
- moved the tailpiece vertically; now, as you can see on this link, the tailpiece has slots, not holes:
http://www.archtopguitarsandbooks.co...?id_product=80
- I put the low E string ball end in the hollow part or the tailpiece and pushed the string end up into the slot, instead of inserting the other end of the string and pulling it.
This way, instead of having all the thick part of the string through the slot, I only had to insert the string end, which was somehow flattened while being pushed into the slot.
Last time I was able to do the same leaving the tailpiece in place, because the low E slot is quite easy to reach even with the other strings mounted.
I hope this is clear enough: English is not my native language and this is a bit difficult to explain precisely without a picture.Last edited by rgiaccio; 01-26-2014 at 07:26 PM.
-
I actually installed TI Swing 14's on an 880. Only the bottom E was snug at first. With some determination it will pull through. You could make the job easier by lightly lubing the hole before pulling the string through. I didn't need to do that.
-
Originally Posted by Jazz_175
When the guitar arrived it had the set I had sent fitted. Not long after I fitted heavier Bensons .014 to.056.
No problems.
Now I use Swing .012 to .050
No problems.
I was originally told that the guitar was only made for .012 D'Addario set and bigger strings would not fit.
I made a fuss.
Something along the lines of "it's a jazz guitar.......right?"
-
>>> When the guitar arrived it had the set I had sent fitted. Not long after I fitted heavier Bensons .014 to.056.
>>> No problems.
>>> Now I use Swing .012 to .050
>>> No problems.
It's a Christmas miracle.
-
-
I've just changed the strings on my new AR880 Pisano twice, experimenting with different gauges. La Bella tape wound 0.14s and TI flatwounds 0.12s. There's a knack to getting those lower strings through the tailgate slots, without having to alter anything. Don't try to thread it through from the end. Instead, place the ball end as close to the slot as possible, then using a credit card or similar, slide it into the tailgate and under the ball end and raise it until it slots in. I can post some photos if it helps.
-
I just got an AR880 John Pisano recently and changed the strings a few times to try out different gauges: La Bella tapewound 0.14s and T-I flatwound 0.12s. Admittedly, it was tough getting the lower strings through those slots but I found a knack without having to alter anything. As rgaccio says above, don't try to pull the string all the way through. Place the ball end as close as possible to the slot, slide a credit card or similar under the tailgate and use it to lift the ball end level with the slot and then pull the string into place. Ok, it's a bit fiddly and I wouldn't want to change a string during a gig, but isn't that why we love our archtops, for their quirkiness ?
-
Originally Posted by Jazz_175
-
You can also gently slice the silk with a blade, then peel it off if it won’t easily go through the tailpiece hole.
-
Ha!
Austrian strings meet Chinese hardware - what could possibly go wrong?
I'd just grind the low E slot on the metal tailpiece claw to accommodate the fatter wrap. It's hidden by the wood. No big whoop.
Grant Green, What is This Thing
Yesterday, 01:59 PM in Ear Training, Transcribing & Reading